Refinishing A Dining Room Table

Refinishing A Dining Room Table Allow it to dry for 24 hours.

Then use a second stripping pad dampened with water to help rinse away the remaining residue. Once dry sand lightly with the 220-grit sandpaper for a smooth finish then wipe away dust and residue with a tack cloth. See my step by step video of How to Strip Sand Stain and Finish a Wooden Tablepa. You will likely need several coats.

Choose a well-ventilated space like a garage.

Eventually Ill build a new one. Finish Sanding With Fine Grit Paper. Repeat this process applying at least two coats of stain to achieve the best results. Once youve sanded the entire table change the sandpaper on the block to 220-grit and sand the table surface a second time.

Read Also : wirecutter dining table  west elm mid century dining table review  whitewash dining table 

Lay down a tarp preferably one that can be easily swept or vacuumed after sanding. Splendid

Go over all areas to remove any residue from stripping and even out imperfections. You simply place the side with the horizontal ridges on top of the fill and gently rub it back and forth until the filled gouge is completely level with the surface of your table. First sand off the old finish. Sand and prime dining chairs and table.

I only did the top just to get a little more life out of it. Wet-Sand Before Final Coats. How to Apply Lacquer. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube.

Dining Table finish 4 coats of Antique Walnut Gel Stain plus a few dabs of Gray Gel Stain. It didnt turn out too bad. How to Refinish a Dark Wood Table Strip the paint. I simply pour the poly into a paper bowl dip the cloth into the finish and spread it on the tabletop.

Spray a thin coat one pass and let it dry 30min-1hr Then sand with 300 grit sand paper and spray another coat. 5 I used the Wax Wash Remover to clean the table one more time before I moved on to staining. Wipe all parts of your dining table with a tack cloth to remove any traces of dust created by sanding. Let dry 24 hours.

Doing this will allow you to clean the table deeply. Stain the wood using a foam brush or rag going with the wood grain. After the final coat of stain has been thoroughly cured typically overnight or 24 hours apply polyurethane according to the manufacturers instructions or Tung oil. Rub the excess stain off before it dries.

If the table is in a very bad condition it can be torn if it is previously painted or varnished. Thin coats level out better and dry faster than thick ones. Sand your table down using 80 grit sandpaper then move to 120 then finish off with 220 grit. Simply wipe the surface again with Mineral Spirits until the surface is completely clean.

If your sandpaper gets gummed up it just means that theres still residue from the Citristrip or the original finish. Let the stain sit overnight. You will spray anywhere between 8-12 inches from the surface area. Sand the entire surface down to make sure all the original finish and any residue is gone.

Applying a top coat especially for a dining table is of utmost importance. Paint dining table and chairs with your chosen paint following manufacturers instructions on the can. I like to use a mini foam roller on the tabletop itself it gives a smoother finish without brush marks. Once all of the finish is removed from the entire table the top legs skirt etc its usually a good idea to give your table a once-over with a finer grit sandpaper like 120-grit to smooth out the finish.

6 Finally it was time to stain. However a gap of 24 hours between applying the finish and staining would be damn effective. Use a stripping pad to apply After Wash to a small section scrubbing it into the wood in small circles. Dont wipe on too much at one time.

Step 4 Sealing the surface with a durable top coat. Let dry 24 hours. The first thing you need to do when refinishing a piece of furniture is strip off as much of the old paint as possible using a paint stripper. I used Citristrip which is less harsh smelling and more environmentally friendly than your traditional paint strippers.

Next clean all dust from the table and apply the stain. This will probably take about an hour or two and youll want to do it outside if possible. Lacquer will be a great finishing topcoat for a dining room table since the durability allows for accidents without harm to the wood. Leave the table after staining for at least 12 hours.

This really helps clear away the rest of the finish and most of the stain as well. This might be especially helpful on the table top surface itself. Clean the table thoroughly. If you want to know how to refinish a dining room table then you need to strip the surface perfectly.

Use only aerosol spray lacquer when coating your furniture. My old table needed a facelift. Shake your can until the ball barely makes a rattling sound. The table may be painted or varnished then you need to tear off that surface.

You might also consider routing the edges of your table to match other furniture in the dining room.